Paccar

PACCAR MX (2004 Emissions) Fault Code: U1073 Humidity Sensor – CAN, Message Time-Out

SET CONDITIONS:
The PCI ECU (D420) lost communication with the humidity sensor (F852).

DIAGNOSTIC CONDITION:
This diagnostic runs continuously when the ignition is on.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
This DTC changes to inactive after the ignition is keyed off for at least 15 seconds and keyed on again, and the fault is no longer detected.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. E-CAN communication
2. Faulty humidity sensor

ADDITIONAL INFORMATION:
The humidity sensor is a smart sensor that communicates with the PCI ECU via E-CAN. The sensor measures the following three properties of the drawn in pre-compressor (VTG turbo charger) air in the inlet air pipe:
1. Relative humidity
2. Pressure
3. Temperature

PACCAR MX (2004 Emissions) Fault Code: U1074 Inlet Air Temperature Before Compressor – Data Erratic, Intermittent or Incorrect

SET CONDITIONS:
The PCI ECU (D420) receives a CAN message from the humidity sensor (F852) that contains an out-of-range value for the temperature.

DIAGNOSTIC CONDITION:
This diagnostic runs continuously when the ignition is on.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
This DTC changes to inactive after the ignition is keyed off for at least 15 seconds and keyed on again, and the fault is no longer detected.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. E-CAN communication
2. Faulty humidity sensor

ADDITIONAL INFORMATION:
The humidity sensor is a smart sensor that communicates with the PCI ECU via E-CAN. The sensor measures the following three properties of the drawn in pre-compressor (VTG turbo charger) air in the inlet air pipe:
1. Relative humidity
2. Pressure
3. Temperature

PACCAR MX (2004 Emissions) Fault Code: U1104 CAN – Message (ACC1) Time-Out from Advanced Emergency Braking System

SET CONDITIONS:
This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

POSSIBLE CAUSES:
1. Wiring issues (interruption or contact resistance)
2. Defective components
3. Incorrect software configuration

PACCAR MX (2004 Emissions) Fault Code: U1105 CAN Communication – Message (PROBA_BBM_to_Eng) Out of Range, Engine Stop from Body Builder Module

SET CONDITIONS:
This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. A corrupt or empty CAN message
2. A malfunction in the system from which the message originates

ADDITIONAL INFORMATION:
1. A ‘message out of range’ DTC is activated by the receiving ECU but indicates a malfunction within another system which communicates with this ECU.
2. The cause of the DTC must be sought in the system from which it originates.

Example:
1. [ECU 1] detects an incorrect or missing signal from [sensor A].
2. [ECU 1] sets [DTC 1] (In this specific case, an open circuit DTC).
3. [ECU 1] constantly informs [ECU 2] about the status of [sensor A] via CAN messages.
4. Since the data received from the sensor is not available or not plausible, an ’empty’ CAN message is sent from [ECU 1] to [ECU 2].
5. [ECU 2] interprets the empty message as being out of the expected range and sets the ‘out of range DTC’ [DTC 2].

PACCAR MX (2004 Emissions) Fault Code: U1110 CAN – Message (RC_DR) Time-Out from Retarder System

SET CONDITIONS:
This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. Wiring issues (interruption or contact resistance)
2. Defective components
3. Incorrect software configuration

PACCAR MX (2004 Emissions) Fault Code: U1112 CAN – Message (SCR1) Time-Out from Aftertreatment System

SET CONDITIONS:
This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. Wiring issues (interruption or contact resistance)
2. Defective components
3. Incorrect software configuration

PACCAR MX (2004 Emissions) Fault Code: U1114 CAN – Message (AT1T1l) Time-Out, DEF Tank Information from Aftertreatment System

SET CONDITIONS:
This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. Wiring issues (interruption or contact resistance)
2. Defective components
3. Incorrect software configuration

PACCAR MX (2004 Emissions) Fault Code: U1118 CAN Communication – Message (EXH_GAS_CORR) Out of Range, NOx After SCR Reading Stable from Aftertreatment System

SET CONDITIONS:
This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. A corrupt or empty CAN message
2. A malfunction in the system from which the message originates

ADDITIONAL INFORMATION:
1. A ‘message out of range’ DTC is activated by the receiving ECU but indicates a malfunction within another system which communicates with this ECU.
2. The cause of the DTC must be sought in the system from which it originates.

Example:
1. [ECU 1] detects an incorrect or missing signal from [sensor A].
2. [ECU 1] sets [DTC 1] (In this specific case, an open circuit DTC).
3. [ECU 1] constantly informs [ECU 2] about the status of [sensor A] via CAN messages.
4. Since the data received from the sensor is not available or not plausible, an ’empty’ CAN message is sent from [ECU 1] to [ECU 2].
5. [ECU 2] interprets the empty message as being out of the expected range and sets the ‘out of range DTC’ [DTC 2].

PACCAR MX (2004 Emissions) Fault Code: U111A CAN Communication – Message (EXH_GAS_CORR) Out of Range, Engine Out NOx Reading Stable from Aftertreatment System

SET CONDITIONS:
This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. A corrupt or empty CAN message
2. A malfunction in the system from which the message originates

ADDITIONAL INFORMATION:
1. A ‘message out of range’ DTC is activated by the receiving ECU, but indicates a malfunction within another system which communicates with this ECU.
2. The cause of the DTC must be sought in the system from which it originates.

Example:
1. [ECU 1] detects an incorrect or missing signal from [sensor A].
2. [ECU 1] sets [DTC 1] (In this specific case, an open circuit DTC).
3. [ECU 1] constantly informs [ECU 2] about the status of [sensor A] via CAN messages.
4. Since the data received from the sensor is not available or not plausible, an ’empty’ CAN message is sent from [ECU 1] to [ECU 2].
5. [ECU 2] interprets the empty message as being out of the expected range and sets the ‘out of range DTC’ [DTC 2].