Detroit Diesel

DESCRIPTION:Proportional valve bank 2 circuit failed Low. MONITORED PARAMETER:Proportional valve bank 2 circuit. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:Always enabled TYPICAL DURATION:Two seconds DASH LAMPS:1. MIL2. CEL ENGINE REACTION:25% Derate VERIFICATION:Ignition Key Cycle. PROBABLE CAUSES:1. Short to ground between the rear valve cover fuel injector harness and the medium (rear) engine brake solenoid.2. Failed EGR valve.3. Short to ground between pin 62 of the 120-pin ECM Connection and the EGR valve actuator/rear valve cover fuel injector harness connectors.4. Short to ground between pin 64 of the 120-pin ECM connection and the electronic dosing valve/fuel cutoff valve connector.5. Failed...

DESCRIPTION:This Code Sets When the Aftertreatment Control Module (ACM) Detects a Short to Power on Pins 9, 15, or 39 within One Second After the Ignition has Been Turned On. MONITORED PARAMETER:High side digital output 3 circuit. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:One second after the ignition is cycled on. TYPICAL DURATION:1 Second DASH LAMPS:1. MIL2. CEL ENGINE REACTION:None VERIFICATION:Cycle the ignition key from the off position to the on position. PROBABLE CAUSES:1. Doser heater.2. Doser heater lines 1, 2, 3, or 4.3. ACM (Aftertreatment Control Module) failure.4. Short to battery between ACM pins 9, 15, 39, or...

DESCRIPTION:Motor Control Module (MCM) internal injector power supply failed high. MONITORED PARAMETER:MCM internal injector power supply. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:Always Enabled TYPICAL DURATION:2 Second DASH LAMPS:1. MIL2. CEL ENGINE REACTION:Derate 25% VERIFICATION:Engine Idle (1 minute). PROBABLE CAUSES:1. Doser heater.2. Doser heater lines 1, 2, 3, or 4.3. ACM (Aftertreatment Control Module) failure.4. Short to battery between ACM pins 9, 15, 39, or 2 and their components.5. Reconnect items in #4 one at a time and clear the fault code after each connection. When fault becomes active, replace the components. Detroit DD13 EPA10 (2010-13) Fault Code: SPN...

DESCRIPTION:This code sets when the aftertreatment control module (ACM) detects a short to ground on pins 9, 15, or 39. MONITORED PARAMETER:High side digital output 3 circuit. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:Always enabled TYPICAL DURATION:Two seconds DASH LAMPS:1. MIL2. CEL ENGINE REACTION:None VERIFICATION:Cycle the ignition key from the off position to the on position. PROBABLE CAUSES:1. Doser heater.2. Doser heater lines 1, 3, or 4.3. ACM (Aftertreatment Control Module) failure.4. Short to battery between ACM pins 9, 15, 39, or 2 and their components.5. Reconnect items in #4 one at a time and clear the fault code...

DESCRIPTION:Motor Control Module (MCM) internal fuel injector power supply failed low. MONITORED PARAMETER:MCM internal fuel injector power supply. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:Always enabled TYPICAL DURATION:Two seconds DASH LAMPS:1. MIL2. CEL ENGINE REACTION:Derate 25% VERIFICATION:Engine Idle (1 minute). PROBABLE CAUSES:1. Doser heater.2. Doser heater lines 1, 3, or 4.3. ACM (Aftertreatment Control Module) failure.4. Short to battery between ACM pins 9, 15, 39, or 2 and their components.5. Reconnect items in #4 one at a time and clear the fault code after each connection. When fault becomes active, replace the components. Detroit DD13 EPA10 (2010-13) Fault Code:...