Detroit Diesel

DESCRIPTION:This code sets when the aftertreatment control module (ACM) detects a short to power on pins 9,15, 39 within one second after the ignition has been turned on. MONITORED PARAMETER:High side digital output 3 circuit. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:One second after the ignition is cycled on. TYPICAL DURATION:Two seconds DASH LAMPS:1. MIL2. CEL ENGINE REACTION:None VERIFICATION:Cycle the ignition key from the off position to the on position. PROBABLE CAUSES:1. Doser heater.2. Doser heater lines 1, 2, 3, or 4.3. ACM (Aftertreatment Control Module) failure.4. Short to battery between ACM pins 9, 15, 39, or 2 and...

DESCRIPTION:Motor Control Module (MCM) internal injector power supply failed high. MONITORED PARAMETER:MCM internal injector power supply. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:Always Enabled TYPICAL DURATION:2 Second DASH LAMPS:1. MIL2. CEL ENGINE REACTION:Derate 25% VERIFICATION:Engine Idle (1 minute). PROBABLE CAUSES:1. Doser heater.2. Doser heater lines 1, 2, 3, or 4.3. ACM (Aftertreatment Control Module) failure.4. Short to battery between ACM pins 9, 15, 39, or 2 and their components.5. Reconnect items in #4 one at a time and clear the fault code after each connection. When fault becomes active, replace the components. Detroit DD16 GHG14 (2014-16) Fault Code: SPN...

DESCRIPTION:This code sets when the aftertreatment control module (ACM) detects a short to ground on pins 9, 15, or 39. MONITORED PARAMETER:High side digital output 3 circuit. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:Always enabled TYPICAL DURATION:Two seconds DASH LAMPS:1. MIL2. CEL ENGINE REACTION:None VERIFICATION:Cycle the ignition key from the off position to the on position. PROBABLE CAUSES:1. Doser heater.2. Doser heater lines 1, 3, or 4.3. ACM (Aftertreatment Control Module) failure.4. Short to battery between ACM pins 9, 15, 39, or 2 and their components.5. Reconnect items in #4 one at a time and clear the fault code...

DESCRIPTION:Motor Control Module (MCM) internal fuel injector power supply failed low. MONITORED PARAMETER:MCM internal fuel injector power supply. TYPICAL ENABLING CONDITIONS:Always enabled MONITOR SEQUENCE:None EXECUTION FREQUENCY:Always enabled TYPICAL DURATION:Two seconds DASH LAMPS:1. MIL2. CEL ENGINE REACTION:Derate 25% VERIFICATION:Engine Idle (1 minute). PROBABLE CAUSES:1. Doser heater.2. Doser heater lines 1, 3, or 4.3. ACM (Aftertreatment Control Module) failure.4. Short to battery between ACM pins 9, 15, 39, or 2 and their components.5. Reconnect items in #4 one at a time and clear the fault code after each connection. When fault becomes active, replace the components. Detroit DD16 GHG14 (2014-16) Fault Code:...

NOTE: Please see the step by step troubleshooting procedures for this specific code. PROBABLE CAUSES:1. DPF inlet pressure sensor.2. Short to power between the 120-pin connector and the DPF inlet and outlet pressure sensors. Detroit DD16 GHG14 (2014-16) Fault Code: SPN 3599 FMI 4 (MCM) Motor Control Module Internal Fuel Injector Power Supply Failed Low Detroit DD16 GHG14 (2014-16) Fault Code: SPN 3599 FMI 4 (ACM) High Side Digital Output 3 Circuit Failed Low Detroit DD16 GHG14 (2014-16) Fault Code: SPN 3599 FMI 3 (MCM) Motor Control Module Internal Injector Power Supply Failed High Detroit DD16 GHG14 (2014-16) Fault Code:...