Paccar– Page 288– ⛽ Diezel365


Paccar

PACCAR MX (2004 Emissions) Fault Code: U1833 CAN Communication – Message (PROPB_VIC) Out of Range, Requested Percent Coolant Pump Speed from Vehicle Control System

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1833 CAN Communication – Message (PROPB_VIC) Out of Range, Requested Percent Coolant Pump Speed from Vehicle Control System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1835 VTG Turbocharger Actuator – CAN, Message Time-Out

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1835 VTG Turbocharger Actuator – CAN, Message Time-Out SET CONDITIONS:The PCI ECU (D420) detects that communication with the VTG turbocharger actuator (L037) is lost or intermittent. DIAGNOSTIC CONDITION:This diagnostic runs continuously when the ignition is on. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:This DTC changes to inactive after the ignition is keyed off for at least 15 seconds and keyed on again, and the fault is no longer detected. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No, repair...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1836 CAN Communication – Message (PTO) Out of Range, Engine Remote PTO Governor Variable Speed Control Switch

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1836 CAN Communication – Message (PTO) Out of Range, Engine Remote PTO Governor Variable Speed Control Switch SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3....

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1837 CAN Communication – Message (PTO) Out of Range, Engine Remote PTO Governor Preprogrammed Speed Control Switch

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1837 CAN Communication – Message (PTO) Out of Range, Engine Remote PTO Governor Preprogrammed Speed Control Switch SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3....

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1838 CAN Communication – Message (PTO) Out of Range, Engine PTO Governor Enable Switch

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1838 CAN Communication – Message (PTO) Out of Range, Engine PTO Governor Enable Switch SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC...

Read more →