Paccar– Page 287– ⛽ Diezel365


Paccar

PACCAR MX (2004 Emissions) Fault Code: U182C CAN Communication – Message (PROPB_VIC) Out of Range, Km h, Miles h, Switch from Vehicle Control System

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U182C CAN Communication – Message (PROPB_VIC) Out of Range, Km h, Miles h, Switch from Vehicle Control System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U182E CAN Communication – Message (PROPB_VIC) Not Available, Primary Retarder by Stalk on from Vehicle Control System

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U182E CAN Communication – Message (PROPB_VIC) Not Available, Primary Retarder by Stalk on from Vehicle Control System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is not available. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No, repair successful– Yes,...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1830 CAN Communication – Message (PROPB_VIC) Out of Range, Primary Retarder by Stalk Off from Vehicle Control System

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1830 CAN Communication – Message (PROPB_VIC) Out of Range, Primary Retarder by Stalk Off from Vehicle Control System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1831 CAN Communication – Message (PROPB_VIC) Not Available, Primary Retarder by Foot On from Vehicle Control System

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1831 CAN Communication – Message (PROPB_VIC) Not Available, Primary Retarder by Foot On from Vehicle Control System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is not available. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No, repair successful– Yes,...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1832 CAN Communication – Message (PROPB_VIC) Out of Range, Primary Retarder by Foot On from Vehicle Control System

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1832 CAN Communication – Message (PROPB_VIC) Out of Range, Primary Retarder by Foot On from Vehicle Control System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set...

Read more →