Paccar

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1938 PID: SPN: 3597 FMI: 1 ECU Power Output Supply Voltage 1 – Data Valid but Below Normal Operational Range – Moderately Severe Level. Low battery voltage detected by the VGT actuator.

Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM.

This fault code is logged when the voltage to the VGT actuator drops below +10-VDC. The VGT will still continue to respond to commands from the primary engine ECM.

Possible repairs:

1)Tighten the loose connections and clean the terminals.
2)Charge or replace the batteries.
3)Repair or replace the OEM power harness.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1922 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Most Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1921 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1911 (ISC/ISL) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level. The ECM has detected that fuel pressure in the rail fuel is higher than the commanded pressure.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1911 (ISB/QSB3.3) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level. The ECM has detected that fuel pressure in the rail fuel is higher than the commanded pressure.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1899 PID: 411 SPN: 411 FMI: 1 Exhaust Gas Recirculation (EGR) Valve Delta Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level. The EGR differential pressure sensor has detected low EGR gas flow or the EGR differential pressure reading is not valid for engine operating conditions.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1896 PID: SID 146 SPN: 2791 FMI: 13 EGR Valve Controller – Out of Calibration. The EGR valve has failed the automatic calibration procedure at initial key-on.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1942 PID: 101 SPN: 101 FMI: 2 Crankcase Pressure – Data Erratic, Intermittent, or Incorrect. The ECM has detected that the crankcase pressure signal is not changing with engine operating conditions.

Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM.

This fault code can be caused by a crankcase breather hose disconnected between the engine outlet and the crankcase filter assembly on engines with an externally mounted crankcase filter option.

This check is only performed at keyswitch OFF, during the ECM powerdown. During this diagnostic check, the ECM monitors the value of the crankcase pressure sensor. If this value is outside of a specified range, Fault Code 1942 is set active at the next key ON.

Possible causes:

1)Resistance in the wiring harness
2)A malfunctioning in-range pressure sensor.

This fault code can be triggered if the crankcase pressure sensor is not installed correctly in the housing.

Possible repairs:

1)Install the oil fill cap properly.
2)Clean or replace the crankcase breather outlet hose.
3)Clean or replace and properly connect the crankcase breather hose.
4)Replace the crankcase pressure sensor.
5)Replace the crankcase breather filter element.
6)If necessary, calibrate the ECM.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1938 PID: SPN: 3597 FMI: 1 ECU Power Output Supply Voltage 1 – Data Valid but Below Normal Operational Range – Moderately Severe Level. Low battery voltage detected by the VGT actuator.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1922 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Most Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1921 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1911 (ISC/ISL) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level. The ECM has detected that fuel pressure in the rail fuel is higher than the commanded pressure.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1911 (ISB/QSB3.3) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level. The ECM has detected that fuel pressure in the rail fuel is higher than the commanded pressure.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1899 PID: 411 SPN: 411 FMI: 1 Exhaust Gas Recirculation (EGR) Valve Delta Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level. The EGR differential pressure sensor has detected low EGR gas flow or the EGR differential pressure reading is not valid for engine operating conditions.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1943 PID: SPN: 3555 FMI: 1 Ambient Air Density – Data Valid but Below Normal Operational Range – Least Severe Level. Engine torque has been reduced because the vehicle was operating at a high altitude condition.

Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM.

When the engine has been operated in a high altitude location, this fault code is logged. This fault code is for information only and no repairs are necessary. The engine can possibly be derated when operating in the high altitude location to protect the turbocharger and engine from excessively high exhaust temperatures. The derate limits the torque output of the engine to keep the temperatures below the maximum temperature limits.

Note: This fault code will most likely not be active with no load in the shop. The engine must be under the same operating condition (altitude and temperature) at the time that it had originally logged.

Possible repairs:

1)Replace the barometric pressure sensor.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1942 PID: 101 SPN: 101 FMI: 2 Crankcase Pressure – Data Erratic, Intermittent, or Incorrect. The ECM has detected that the crankcase pressure signal is not changing with engine operating conditions.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1938 PID: SPN: 3597 FMI: 1 ECU Power Output Supply Voltage 1 – Data Valid but Below Normal Operational Range – Moderately Severe Level. Low battery voltage detected by the VGT actuator.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1922 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Most Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1921 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1911 (ISC/ISL) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level. The ECM has detected that fuel pressure in the rail fuel is higher than the commanded pressure.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1911 (ISB/QSB3.3) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level. The ECM has detected that fuel pressure in the rail fuel is higher than the commanded pressure.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 195 (2 wire sensor) PID: 111 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at engine coolant level circuit.

Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM.

Possible causes:

1)Open return or signal circuit in the harness, connectors, or sensor
2)Signal wire shorted to sensor supply or battery voltage.

Possible repairs:

1)Replace the engine coolant level sensor.
2)Repair or replace the OEM harness.
3)Replace the ECM.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 155 PID: 105 SPN: 105 FMI: 0 Intake Manifold 1 Temperature – Data Valid but Above Normal Operational Range – Most Severe Level. Intake manifold air temperature signal indicates intake manifold air temperature above engine protection critical limit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 154 PID: 105 SPN: 105 FMI: 4 Intake Manifold 1 Temperature Sensor Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at intake manifold air temperature circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 153 PID: 105 SPN: 105 FMI: 3 Intake Manifold 1 Temperature Sensor Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at intake manifold air temperature circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 151 PID: 110 SPN: 110 FMI: 0 Engine Coolant Temperature – Data Valid But Above Normal Operational Range – Most Severe Level. Engine coolant temperature signal indicates engine coolant temperature above engine protection critical limit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 146 PID: 110 SPN: 110 FMI: 0 Engine Coolant Temperature – Data Valid But Above Normal Operational Range – Moderately Severe Level. Engine coolant temperature is above engine protection warning limit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 145 PID: 110 SPN: 110 FMI: 4 Engine Coolant Temperature 1 Sensor Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at engine coolant temperature circuit.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 195 (3 wire sensor) PID: 111 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at engine coolant level circuit.

Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM.
Possible causes:

1)Open return circuit in the engine harness, connectors, or sensor
2)Signal circuit shorted to sensor supply or battery voltage
3)Sensor supply circuit shorted to battery voltage.

Possible repairs:

1)Replace the engine coolant level sensor.
2)Replace the ECM.
3)Repair or replace the OEM harness.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 195 (2 wire sensor) PID: 111 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at engine coolant level circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 155 PID: 105 SPN: 105 FMI: 0 Intake Manifold 1 Temperature – Data Valid but Above Normal Operational Range – Most Severe Level. Intake manifold air temperature signal indicates intake manifold air temperature above engine protection critical limit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 154 PID: 105 SPN: 105 FMI: 4 Intake Manifold 1 Temperature Sensor Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at intake manifold air temperature circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 153 PID: 105 SPN: 105 FMI: 3 Intake Manifold 1 Temperature Sensor Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at intake manifold air temperature circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 151 PID: 110 SPN: 110 FMI: 0 Engine Coolant Temperature – Data Valid But Above Normal Operational Range – Most Severe Level. Engine coolant temperature signal indicates engine coolant temperature above engine protection critical limit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 146 PID: 110 SPN: 110 FMI: 0 Engine Coolant Temperature – Data Valid But Above Normal Operational Range – Moderately Severe Level. Engine coolant temperature is above engine protection warning limit.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 196 (2 wire sensor) PID: 111 SPN: 111 FMI: 4 Coolant Level Sensor 1 Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at the engine coolant level circuit.

Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM.

Possible causes:

1)Signal circuit shorted to ground or return in the harness, sensor, or connectors.

Possible repairs:

1)Replace the engine coolant level sensor.
2)Repair or replace the OEM harness.
3)Replace the ECM.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 195 (3 wire sensor) PID: 111 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at engine coolant level circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 195 (2 wire sensor) PID: 111 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at engine coolant level circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 155 PID: 105 SPN: 105 FMI: 0 Intake Manifold 1 Temperature – Data Valid but Above Normal Operational Range – Most Severe Level. Intake manifold air temperature signal indicates intake manifold air temperature above engine protection critical limit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 154 PID: 105 SPN: 105 FMI: 4 Intake Manifold 1 Temperature Sensor Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at intake manifold air temperature circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 153 PID: 105 SPN: 105 FMI: 3 Intake Manifold 1 Temperature Sensor Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at intake manifold air temperature circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 151 PID: 110 SPN: 110 FMI: 0 Engine Coolant Temperature – Data Valid But Above Normal Operational Range – Most Severe Level. Engine coolant temperature signal indicates engine coolant temperature above engine protection critical limit.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 196 (3 wire sensor) PID: 111 SPN: 111 FMI: 4 Coolant Level Sensor 1 Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at engine coolant level circuit.

Verify the ECM calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM.

Possible causes:

1)Open signal circuit in the engine harness, connectors, or sensor
2)Signal circuit shorted to ground in the engine harness, connector, or sensor
3)Damaged sensor.

Possible repairs:

1)Replace the engine coolant level sensor.
2)Repair or replace the OEM harness.
3)Replace the ECM.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 196 (2 wire sensor) PID: 111 SPN: 111 FMI: 4 Coolant Level Sensor 1 Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at the engine coolant level circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 195 (3 wire sensor) PID: 111 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at engine coolant level circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 195 (2 wire sensor) PID: 111 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at engine coolant level circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 155 PID: 105 SPN: 105 FMI: 0 Intake Manifold 1 Temperature – Data Valid but Above Normal Operational Range – Most Severe Level. Intake manifold air temperature signal indicates intake manifold air temperature above engine protection critical limit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 154 PID: 105 SPN: 105 FMI: 4 Intake Manifold 1 Temperature Sensor Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at intake manifold air temperature circuit.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 153 PID: 105 SPN: 105 FMI: 3 Intake Manifold 1 Temperature Sensor Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at intake manifold air temperature circuit.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1962 PID: SID 027 SPN: 641 FMI: 0 VGT Actuator Driver Over Temperature (Calculated) – Data Valid but Above Normal Operational Range – Least Severe Level. High Internal VGT actuator temperature has been detected.

Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM.

This fault code will log when the internal temperature of the VGT actuator exceeds 125°C [257°F].

This fault code will be inactive when the vehicle is in the shop because the VGT actuator temperature has cooled down.

Troubleshoot multiple inactive counts of this fault code as an active fault code.

Also check for exhaust leaks blowing on the VGT actuator. Repair any external leaks.

Possible repairs:

1)Repair or replace the blocked coolant line.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1943 PID: SPN: 3555 FMI: 1 Ambient Air Density – Data Valid but Below Normal Operational Range – Least Severe Level. Engine torque has been reduced because the vehicle was operating at a high altitude condition.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1942 PID: 101 SPN: 101 FMI: 2 Crankcase Pressure – Data Erratic, Intermittent, or Incorrect. The ECM has detected that the crankcase pressure signal is not changing with engine operating conditions.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1938 PID: SPN: 3597 FMI: 1 ECU Power Output Supply Voltage 1 – Data Valid but Below Normal Operational Range – Moderately Severe Level. Low battery voltage detected by the VGT actuator.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1922 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Most Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1921 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1911 (ISC/ISL) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level. The ECM has detected that fuel pressure in the rail fuel is higher than the commanded pressure.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1966 PID: 326 SPN: 3241 FMI: 0 Aftertreatment Exhaust Gas Temperature 1 – Data Valid But Above Normal Operating Range – Most Severe Level.

This fault code is logged when the ECM has detected a high temperature condition in the aftertreatment system and active regeneration of the aftertreatment diesel particulate filter is not occurring. The fault code indicates that a secondary fuel source is entering the aftertreatment system and is creating a temperature increase across the aftertreatment diesel oxidation catalyst and/or aftertreatment diesel particulate filter.

Possible causes:

1)Excessive engine oil or diesel fuel being introduced into the exhaust system from the engine
2)A damaged engine fuel injector causing unburned diesel fuel to enter the exhaust system
3)The aftertreatment diesel oxidation catalyst inlet temperature sensor failed in-range
4)The aftertreatment diesel particulate filter inlet temperature sensor failed in-range
5)The aftertreatment diesel particulate filter outlet temperature sensor failed in-range
6)An in-range engine sensor malfunction has occurred, causing excessive fuel to enter the exhaust system.

The aftertreatment system must be inspected after making the appropriate repair outlined in this fault code troubleshooting tree. Progressive damage to the aftertreatment system may have occurred. Remove the exhaust aftertreatment system from the vehicle to inspect it for potential damage and reuse. For ISB CM2150 engines, use the following procedure in the ISB CM2150 Service Manual, Bulletin 4021578. Refer to Procedure 014-013 in Section 14. For ISC and ISL CM2150 engines, use the following procedure in the ISC and ISL CM2150 Service Manual, Bulletin 4021569.

Possible repairs:

1)Repair or replace any damaged components.
2)Replace the injector.
3)Repair or replace any components that caused the engine oil or diesel fuel contamination.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1962 PID: SID 027 SPN: 641 FMI: 0 VGT Actuator Driver Over Temperature (Calculated) – Data Valid but Above Normal Operational Range – Least Severe Level. High Internal VGT actuator temperature has been detected.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1943 PID: SPN: 3555 FMI: 1 Ambient Air Density – Data Valid but Below Normal Operational Range – Least Severe Level. Engine torque has been reduced because the vehicle was operating at a high altitude condition.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1942 PID: 101 SPN: 101 FMI: 2 Crankcase Pressure – Data Erratic, Intermittent, or Incorrect. The ECM has detected that the crankcase pressure signal is not changing with engine operating conditions.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1938 PID: SPN: 3597 FMI: 1 ECU Power Output Supply Voltage 1 – Data Valid but Below Normal Operational Range – Moderately Severe Level. Low battery voltage detected by the VGT actuator.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1922 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Most Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1921 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.

Leer más →

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1968 PID: SPN: 3249 FMI: 0 Aftertreatment Exhaust Gas Temperature 2 – Data Valid but Above Normal Operational Range – Moderately Severe Level.

This fault code is logged when the ECM has detected a high temperature condition in the aftertreatment system and active regeneration of the aftertreatment diesel particulate filter is occurring. The fault code indicates that a secondary fuel source is entering the aftertreatment system and is creating a temperature increase across the aftertreatment diesel oxidation catalyst and/or aftertreatment diesel particulate filter.

Possible causes:

1)Excessive engine oil or diesel fuel being introduced into the exhaust system from the engine
2)A damaged engine fuel injector causing unburned diesel fuel to enter the exhaust system
3)The aftertreatment diesel particulate filter inlet temperature sensor failed in-range
4)An in-range engine sensor malfunction has occurred, causing excessive fuel to enter the exhaust system.

The aftertreatment system must be inspected after making the appropriate repair outlined in this fault code troubleshooting tree. Progressive damage to the aftertreatment system may have occurred. Remove the exhaust aftertreatment system from the vehicle to inspect it for potential damage and reuse. For ISB CM2150 engines, use the following procedure in the ISB CM2150 Service Manual, Bulletin 4021578. For ISC and ISL CM2150 engines, use the following procedure in the ISC and ISL CM2150 Service Manual, Bulletin 4021569.

Possible repairs:

1)If no short is found, replace the temperature sensor that is reading higher or lower than the other sensors.
2)Repair or replace any components that caused the engine oil or diesel fuel contamination.

PACCAR PX-6 CM2150 (2007-09) Fault Code: 1966 PID: 326 SPN: 3241 FMI: 0 Aftertreatment Exhaust Gas Temperature 1 – Data Valid But Above Normal Operating Range – Most Severe Level. Engine exhaust gas temperatures entering the aftertreatment system are above the engine protection limits.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1962 PID: SID 027 SPN: 641 FMI: 0 VGT Actuator Driver Over Temperature (Calculated) – Data Valid but Above Normal Operational Range – Least Severe Level. High Internal VGT actuator temperature has been detected.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1943 PID: SPN: 3555 FMI: 1 Ambient Air Density – Data Valid but Below Normal Operational Range – Least Severe Level. Engine torque has been reduced because the vehicle was operating at a high altitude condition.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1942 PID: 101 SPN: 101 FMI: 2 Crankcase Pressure – Data Erratic, Intermittent, or Incorrect. The ECM has detected that the crankcase pressure signal is not changing with engine operating conditions.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1938 PID: SPN: 3597 FMI: 1 ECU Power Output Supply Voltage 1 – Data Valid but Below Normal Operational Range – Moderately Severe Level. Low battery voltage detected by the VGT actuator.
PACCAR PX-6 CM2150 (2007-09) Fault Code: 1922 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Most Severe Level. The soot load of the aftertreatment diesel particulate filter has exceeded the recommended limits.

Leer más →

← Anterior 1 … 58 59 60 61 62 … 150 Siguiente →