Paccar– Página 297– ⛽ Diezel365


Paccar

PACCAR MX (2004 Emissions) Fault Code: U1891 CAN Communication – Message (EBC1) Data Not Correct of Available, Anti-Lock Brake System Active from Brake System

Publicado por Diezel Solutions en

PACCAR MX (2004 Emissions) Fault Code: U1891 CAN Communication – Message (EBC1) Data Not Correct of Available, Anti-Lock Brake System Active from Brake System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is not correct or not available. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?–...

Leer más →


PACCAR MX (2004 Emissions) Fault Code: U1892 CAN – Message (PROPB_SCD_1) Time-Out from Predictive Cruise Control

Publicado por Diezel Solutions en

PACCAR MX (2004 Emissions) Fault Code: U1892 CAN – Message (PROPB_SCD_1) Time-Out from Predictive Cruise Control SET CONDITIONS:This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?–...

Leer más →


PACCAR MX (2004 Emissions) Fault Code: U1893 CAN – Message (PROPB_SCD_1) Rate Too High from Predictive Cruise Control

Publicado por Diezel Solutions en

PACCAR MX (2004 Emissions) Fault Code: U1893 CAN – Message (PROPB_SCD_1) Rate Too High from Predictive Cruise Control CORRESPONDING OBD READINESS MONITOR:None REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No, repair successful– Yes, repair unsuccessful PACCAR MX (2004 Emissions) Fault Code: U1892 CAN – Message (PROPB_SCD_1) Time-Out from Predictive Cruise Control PACCAR MX (2004 Emissions) Fault Code: U1891 CAN Communication – Message (EBC1) Data Not Correct of Available, Anti-Lock Brake System Active from Brake System PACCAR MX (2004 Emissions) Fault Code: U1890 CAN...

Leer más →


PACCAR MX (2004 Emissions) Fault Code: U1894 CAN Communication – Message (PROPB_SCD_1) Out of Range, Predictive Cruise Control Set Speed Delta from Predictive Cruise Control

Publicado por Diezel Solutions en

PACCAR MX (2004 Emissions) Fault Code: U1894 CAN Communication – Message (PROPB_SCD_1) Out of Range, Predictive Cruise Control Set Speed Delta from Predictive Cruise Control SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and...

Leer más →


PACCAR MX (2004 Emissions) Fault Code: U1895 CAN Communication – Message (PROPB_SCD_1) Not Available, Predictive Cruise Control Set Speed Delta from Predictive Cruise Control

Publicado por Diezel Solutions en

PACCAR MX (2004 Emissions) Fault Code: U1895 CAN Communication – Message (PROPB_SCD_1) Not Available, Predictive Cruise Control Set Speed Delta from Predictive Cruise Control SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is not available. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No, repair successful–...

Leer más →