Paccar
PACCAR MX (2004 Emissions) Fault Code: U1544 CAN Communication – Message (ERC1_DR) Out of Range, Retarder Torque Actual Percent from Retarder System
Publicado por Diezel Solutions en
PACCAR MX (2004 Emissions) Fault Code: U1544 CAN Communication – Message (ERC1_DR) Out of Range, Retarder Torque Actual Percent from Retarder System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did...
PACCAR MX (2004 Emissions) Fault Code: U1545 CAN Communication – Message (ERC1_DR) Out of Range, Driver’s Demand Retarder – Percent Torque from Retarder System
Publicado por Diezel Solutions en
PACCAR MX (2004 Emissions) Fault Code: U1545 CAN Communication – Message (ERC1_DR) Out of Range, Driver’s Demand Retarder – Percent Torque from Retarder System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs2. Test drive or operate the vehicle to meet the diagnostic conditions and set...
PACCAR MX (2004 Emissions) Fault Code: U1546 CAN Communication – Message (ERC1_DR) Out of Range, Intended Retarder Percent Torque from Retarder System
Publicado por Diezel Solutions en
PACCAR MX (2004 Emissions) Fault Code: U1546 CAN Communication – Message (ERC1_DR) Out of Range, Intended Retarder Percent Torque from Retarder System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did...
PACCAR MX (2004 Emissions) Fault Code: U1547 CAN Communication – Message (ERC1_DR) Out of Range, Retarder Selection, Non-Engine from Retarder System
Publicado por Diezel Solutions en
PACCAR MX (2004 Emissions) Fault Code: U1547 CAN Communication – Message (ERC1_DR) Out of Range, Retarder Selection, Non-Engine from Retarder System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the...
PACCAR MX (2004 Emissions) Fault Code: U1548 CAN Communication – Message (ETC1) Out of Range, Transmission Output Shaft Speed from Transmission System
Publicado por Diezel Solutions en
PACCAR MX (2004 Emissions) Fault Code: U1548 CAN Communication – Message (ETC1) Out of Range, Transmission Output Shaft Speed from Transmission System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did...