Paccar

PACCAR MX (2004 Emissions) Fault Code: U17D2 CAN Communication – Message (TSC1_DXR) Message Checksum from Retarder System

SET CONDITIONS:
This DTC is set when the checksum of the message does not match the checksum calculated by the receiving component.

DIAGNOSTIC CONDITION:
This diagnostic runs continuously when the ignition is on.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
This DTC will change to inactive immediately after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. External interference of the CAN communication
2. Defective component
3. Software incorrect or incompatible

ADDITIONAL INFORMATION:
1. A checksum is a calculated value that is sent together with the CAN message for message validation purposes.
2. Safety critical CAN messages are sent with a checksum to make sure that the message is valid and the content can be accepted.

PACCAR MX (2004 Emissions) Fault Code: U17E4 Remote Pedal – Voltage Too High or Short Circuit to Supply

SET CONDITIONS:
This DTC is set when the ECU detects a higher voltage than expected on the signal or control circuit of the ECU.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. The sensor or actuator signal wiring has a short circuit to supply.
2. A malfunction of the sensor or actuator

PACCAR MX (2004 Emissions) Fault Code: U1802 VTG Turbocharger Actuator Power Supply – Data Valid but Too High

SET CONDITIONS:
The VTG turbo charger actuator (L037) detects that the actuator power supply is above 17 volts for more than 40 seconds.

DIAGNOSTIC CONDITION:
This diagnostic runs continuously when the ignition is on.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
This DTC changes to inactive after the ignition is keyed off and keyed on again and the fault is no longer detected.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. VTG turbocharger actuator power supply, check:
– Whether more ECUs on the vehicle detect incorrect power supply
– Battery voltage (faulty alternator)
– VTG turbocharger actuator power supply
2. Faulty VTG turbo charger actuator if the DTC remains active after the above is performed/checked

ADDITIONAL INFORMATION:
The power supply of the actuator is continuously monitored.

PACCAR MX (2004 Emissions) Fault Code: U1803 CAN Communication – Message (ACC1) Out of Range, Forward Collision Warning from Advanced Emergency Braking System

SET CONDITIONS:
This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. A corrupt or empty CAN message
2. A malfunction in the system from which the message originates

ADDITIONAL INFORMATION:
1. A ‘message out of range’ DTC is activated by the receiving ECU but indicates a malfunction within another system which communicates with this ECU.
2. The cause of the DTC must be sought in the system from which it originates.

Example:
1. [ECU 1] detects an incorrect or missing signal from [sensor A].
2. [ECU 1] sets [DTC 1] (In this specific case, an open circuit DTC).
3. [ECU 1] constantly informs [ECU 2] about the status of [sensor A] via CAN messages.
4. Since the data received from the sensor is not available or not plausible, an ’empty’ CAN message is sent from [ECU 1] to [ECU 2].
5. [ECU 2] interprets the empty message as being out of the expected range and sets the ‘out of range DTC’ [DTC 2].

PACCAR MX (2004 Emissions) Fault Code: U1805 CAN – Message (ACC2) Time-Out from Vehicle Control System

SET CONDITIONS:
This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all.

DIAGNOSTIC CONDITION:
The diagnostic runs continuously when the ignition is keyed on or when the engine is running.

CORRESPONDING OBD READINESS MONITOR:
None

RESET CONDITION:
The DTC changes to inactive after the diagnostic runs and passes.

REPAIR VERIFICATION:
1. Clear all DTCs.
2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.
3. Did the DTC come back?
– No, repair successful
– Yes, repair unsuccessful

POSSIBLE CAUSES:
1. Wiring issues (interruption or contact resistance)
2. Defective components
3. Incorrect software configuration