Cumminz
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2387 PID: SID 027 SPN: 641
Publicado por Diezel Solutions en
Verify the ECM calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM. 1)This fault code is set when the actual VGT actuator position does not meet the commanded position for more than 10 seconds.2)Large boost pressure leaks can also cause this fault code. The aftertreatment system must be inspected after making the appropriate repair outlined in this fault code troubleshooting tree. Progressive damage to the aftertreatment system can possibly have occurred. Perform the aftertreatment initial check procedure to test for a damaged...
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 239 PID: SID 232 SPN: 3511 FMI: 3 Sensor Supply 3 Circuit – Voltage Above Normal or Shorted to High Source. High voltage detected at sensor supply number 3 circuit.
Publicado por Diezel Solutions en
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM. High voltage on the (+) 5 volt supply wire can be caused by a short to battery voltage in the engine harness or connectors, or a damaged ECM. Possible repairs: 1)Replace the ECM.2)Repair or replace the engine harness.Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary,...
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 241 PID: 241 SPN: 84 FMI: 2 Wheel-Based Vehicle Speed – Data Erratic, Intermittent, or Incorrect. The ECM lost the vehicle speed signal.
Publicado por Diezel Solutions en
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM. There are multiple types of vehicle speed sensors. Various types include magnetic pickup, data link, digital, and tachograph. Refer to the OEM for the specific type installed on the vehicle. This fault is set active when the ECM loses a vehicle speed signal when other engine conditions indicate the vehicle is moving. The fault can also become active if there is a series of clutch, service brake....
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 242 PID: 84 SPN: 84 FMI: 10 Wheel-Based Vehicle Speed Sensor Circuit Tampering Has Been Detected – Abnormal Rate of Change. Signal indicates an intermittent connection or VSS tampering.
Publicado por Diezel Solutions en
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM. Verify that the feature settings for the vehicle speed sensor anti-tampering (Fault Code 242), application type and automatic transmission are set correctly. If any of these are set incorrectly for the specific vehicle and application, Fault Code 242 could occur erroneously. Driving techniques such as driving for extended periods of time in lower gears can log Fault Code 242. Fault Code 242 can be logged if the...
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2448 PID: SPN: 111 FMI: 1 Coolant Level – Data Valid but Below Normal Operational Range – Least Severe Level. Low engine coolant level detected.
Publicado por Diezel Solutions en
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM. This fault code goes active when the coolant level inside the radiator top tank or surge tank drops below the sensor level. Fill the top tank with coolant. Possible repairs: 1)Add coolant to the engine.