Cumminz
Cummins ISL CM850 (2003-06) Fault Code: FC0006 PID: SPN: FMI: Exhaust Gas Temperature Sensor Number 1 Circuit – Voltage Above Normal, or Shorted to High Source. High signal voltage or open circuit detected at the Exhaust Gas Temperature Sensor circuit.
Publicado por Diezel Solutions en
Cummins ISL CM850 (2003-06) Fault Code: FC0006 PID: SPN: FMI: Exhaust Gas Temperature Sensor Number 1 Circuit – Voltage Above Normal, or Shorted to High Source. High signal voltage or open circuit detected at the Exhaust Gas Temperature Sensor circuit. Possible causes: 1)Signal circuit shorted to a voltage source or a shorted sensor. This fault code will only be present in the exhaust gas treatment monitor unit and will not be present in the engine electronic control module (ECM). The exhaust gas treatment fault code and maintenance lamps will both flash six times in sequence to alert the operator that...
Cummins ISC CM2150 (2007-09) Fault Code: 111 PID: SID 254 SPN: 629 FMI: 12 Electronic Control Module Critical Internal Failure – Bad Intelligent Device or Component.
Publicado por Diezel Solutions en
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM. This fault code can only be caused by an internal ECM problem. Repairs are not possible for the ECM. Possible repairs: 1)Replace the ECM.
Cummins ISC CM2150 (2007-09) Fault Code: 1117 PID: SID 251 SPN: 627 FMI: 2 Power Supply Lost With Ignition On – Data Erratic, Intermittent, or Incorrect. Supply voltage to the ECM fell below +6.2-VDC momentarily, or the ECM was not allowed to power down
Publicado por Diezel Solutions en
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM. This fault is set active if the ECM battery supply voltage drops below +6.2-VDC while the keyswitch is in the ON position. Make sure the ECM unswitched battery supply is coming directly from the battery and not the starter. If unswitched power is coming from the starter, it is possible for the battery voltage to drop low enough during cranking to set this fault active. Where the...
Cummins ISC CM2150 (2007-09) Fault Code: 115 PID: 115 SPN: 115 FMI: 2 Engine Magnetic Speed/Position Lost Both of Two Signals – Data Erratic, Intermittent, or Incorrect.
Publicado por Diezel Solutions en
Verify the ECM calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. This fault code indicates that the camshaft position sensor and crankshaft position sensor wiring harness connectors are reversed. Possible repairs: 1)If necessary, calibrate the ECM.2)Replace the ECM.
Cummins ISC CM2150 (2007-09) Fault Code: 122 PID: 102 SPN: 102 FMI: 3 Intake Manifold 1 Pressure Sensor Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at the intake manifold pressure circuit.
Publicado por Diezel Solutions en
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM. The intake manifold pressure sensor shares supply and return wires in the engine harness with other sensors. Opens and shorts in the engine harness can cause multiple fault codes to be active. Before troubleshooting Fault Code 122, check for multiple faults. Possible causes: 1)Open return circuit in the engine harness, connectors, or sensor2)Signal wire shorted to sensor supply or battery voltage. Possible repairs: 1)Replace the intake manifold...