Tu carrito
😊 Product added to cart successfully
Product removed to cart successfully
Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 5864 PID: SPN: 5864 FMI: 3/3 Aftertreatment 1 Diesel Exhaust Fluid Pump Command Circuit – Voltage Above Normal or Shorted to High Source
Lamp:Amber
Reason:A short circuit to battery has been detected in the diesel exhaust fluid pump command circuit.
Effect:Possible reduced engine performance.
Circuit Description:The aftertreatment diesel exhaust fluid dosing unit performs many functions, one of which is to generate adequate diesel exhaust fluid pressure in the lines, using a pump, to allow for dosing. The ECM provides a battery voltage supply and a ground to the diesel exhaust fluid dosing unit. The ECM also supplies a signal to the dosing unit to control the diesel exhaust fluid output. This signal changes, based on the diesel exhaust fluid pressure being commanded.
Component Location:The aftertreatment diesel exhaust fluid dosing unit location is Original Equipment Manufacturer (OEM) dependent.
Conditions for Running the Diagnostics:This diagnostic runs when the aftertreatment diesel exhaust fluid dosing unit is commanded ON.
Conditions for Setting the Fault Code:The Engine Control Module (ECM) detected voltage above a calibrated value on the control circuit when the dosing unit was commanded ON.
Action Taken When the Fault Code is Active:1. The ECM illuminates the amber check engine lamp immediately when the diagnostic runs and fails.2. Engine torque will be severely reduced if the engine is operated for an extended period of time with this fault active.
Conditions for Clearing the Fault Code:1. To validate the repair, perform the “aftertreatment diesel exhaust fluid doser pump override test” found under “ECM diagnostic tests” in the recommended diagnostic tool or equivalent.2. The ECM will turn off the amber check engine lamp immediately after the diagnostic runs and passes.3. The fault code status displayed by the recommended diagnostic tool or equivalent will change to inactive immediately after the diagnostic runs and passes.4. The “reset all faults” command in the recommended diagnostic tool or equivalent can be used to clear active and inactive faults.
Shop Talk:Possible causes of this fault code include:Short to battery or ground in the OEM wiring harness.
Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 5838 PID: SPN: 5717 FMI: 10/10 Aftertreatment 1 Outlet NOx Sensor Self-Diagnosis – Abnormal Rate of Change
Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 5656 PID: SPN: 3227 FMI: 10/10 Aftertreatment Outlet Oxygen – Abnormal Rate of Change
Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 4841 PID: SPN: 6653 FMI: 0/16 Engine Injector Metering Rail 1 Cold Start Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level
Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 4729 PID: SPN: 102 FMI: 1/1 Intake Manifold 1 Pressure – Data Valid But Below Normal Operating Range – Most Severe Level
Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 4679 PID: SPN: 1761 FMI: 5/5 Aftertreatment 1 Diesel Exhaust Fluid Tank Level Sensor Circuit – Current Below Normal or Open Circuit
Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 4282 PID: SPN: 5298 FMI: 11/31 Aftertreatment Diesel Oxidation Catalyst Conversion Efficiency – Condition Exists