Paccar
PACCAR PX-8 CM2150 (2007-09) Fault Code: 1911 (ISB/QSB3.3) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level.
Posted by Diezel Solutions on
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM.Fault Code 1911 is activated when the sensed rail fuel pressure reaches the opening pressure of the rail fuel pressure relief valve. Sensed pressure has exceeded system target range. In normal engine operation, the ECM calibration varies the flow commanded to the fuel pump actuator to achieve the correct fuel rail pressure. System failures that cause loss of pressure control can cause the fuel rail pressure relief valve...
PACCAR PX-8 CM2150 (2007-09) Fault Code: 1911 (ISC/ISL) PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level.
Posted by Diezel Solutions on
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM.Fault Code 1911 is activated when the sensed rail fuel pressure reaches the opening pressure of the rail fuel pressure relief valve. Sensed pressure has exceeded system target range. In normal engine operation, the ECM calibration varies the flow commanded to the fuel pump actuator to achieve the correct fuel rail pressure. System failures that cause loss of pressure control can cause the fuel rail pressure relief valve...
PACCAR PX-8 CM2150 (2007-09) Fault Code: 1921 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Moderately Severe Level.
Posted by Diezel Solutions on
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM. Note: This fault code indicates that the aftertreatment diesel particulate filter requires maintenance by performing a stationary regeneration procedure. This is a maintenance procedure only and is not covered by Cummins Inc. warranty. Note: Repeated occurrences of this fault code may indicate the engine requires frequent regeneration. Refer to symptom tree t147 (Aftertreatment Diesel Particulate Filter-Excessive Automatic and/or Stationary Regeneration) to identify the cause of frequent regeneration....
PACCAR PX-8 CM2150 (2007-09) Fault Code: 1922 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter Differential Pressure – Data Valid But Above Normal Operating Range – Most Severe Level.
Posted by Diezel Solutions on
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM. This fault code indicates that the soot load inside the aftertreatment diesel particulate filter has reached the maximum level, soot level stage 4. Regeneration of the aftertreatment diesel particulate filter at this stage is not possible. The aftertreatment diesel particulate filter must be inspected. If it meets the inspection criteria, it can be cleaned using an SPX air pulse, or equivalent, cleaning machine. If it does not...
PACCAR PX-8 CM2150 (2007-09) Fault Code: 1938 PID: SPN: 3597 FMI: 1 ECU Power Output Supply Voltage 1 – Data Valid but Below Normal Operational Range – Moderately Severe Level. Low battery voltage detected by the VGT actuator.
Posted by Diezel Solutions on
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM. This fault code is logged when the voltage to the VGT actuator drops below +10-VDC. The VGT will still continue to respond to commands from the primary engine ECM. Possible repairs: 1)Tighten the loose connections and clean the terminals.2)Charge or replace the batteries.3)Repair or replace the OEM power harness. PACCAR PX-8 CM2150 (2007-09) Fault Code: 1922 PID: SID 324 SPN: 3251 FMI: 0 Aftertreatment Diesel Particulate Filter...