Skip to content

Telegram : @Diezel365

Cummins ISX11.9 CM2250 (2010-12) Fault Code: 212 PID: 175 SPN: 175 FMI: 3 Engine Oil Temperature Sensor 1 Circuit- Voltage Above Normal or Shorted to High Source

Circuit DescriptionThe engine oil temperature sensor is a variable resistor sensor and is used to measure the temperature of the engine oil in the oil rifle. The electronic control module (ECM) supplies 5 volts to the engine oil temperature signal circuit. The ECM monitors the change in voltage caused by changes in the resistance of the sensor to determine the engine oil temperature. When the oil temperature is cold, the sensor or thermistor resistance is high. The ECM signal voltage only pulls down a small amount through the sensor to a ground. Therefore, the ECM senses a high signal voltage or low temperature. When the oil temperature is warm, the sensor resistance is low. The signal voltage pulls down a large amount. Therefore, the ECM senses a low signal voltage or high temperature. The engine oil temperature sensor is used to monitor the engine oil temperature. If the temperature exceeds a calibration limit, an engine protection fault code will be triggered.

Component LocationThe engine oil temperature sensor is located in the oil rifle.

Conditions for Running the DiagnosticsThis diagnostic runs continuously when the keyswitch is in the ON position.

Conditions for Setting the Fault CodesThe ECM detects that the engine oil temperature signal voltage is greater than 5.13-VDC for more than 1 second.

Action Taken When the Fault Code is ActiveThe ECM illuminates the amber CHECK ENGINE lamp and/or the Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails.A default value for the engine oil temperature reading is used.Conditions for Clearing the Fault CodeTo validate the repair, start the engine and let it idle for 1 minute.The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.The ECM will turn off the amber CHECK ENGINE lamp after the diagnostic runs and passes.For OBD engines, the ECM will turn off the MIL after 3 consecutive trips where the diagnostic runs and passes.The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD engines.

Shop TalkThe engine oil temperature sensor shares return wires in the engine harness with other sensors. An open return can cause multiple fault codes to be active.

Possible causes of this fault code include:

Open return circuit in the harness, connectors, or sensor.Open signal circuit or shorted to a voltage source

Possible Cause:1) Engine Oil temperature sensor failure2) ECM failure3) Engine Harness

Cummins ISX11.9 CM2250 (2010-12) Fault Code: 197 PID: 2560 SPN: 111 FMI: 18 Coolant Level- Data Valid But Below Normal Operating Range- Moderately Severe Level
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 196 (3 Wire) PID: 111 SPN: 111 FMI: 4 Coolant Level Sensor 1 Circuit- Voltage Below Normal or Shorted to Low Source
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 196 (2 Wire) PID: 2558 SPN: 111 FMI: 4 Coolant Level Sensor 1 Circuit- Voltage Below Normal or Shorted to Low Source
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 195 (3 Wire) PID: 111 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit- Voltage Above Normal or Shorted to High Source
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 195 (2 Wire) PID: 2559 SPN: 111 FMI: 3 Coolant Level Sensor 1 Circuit- Voltage Above Normal or Shorted to High Source
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 187 PID: SID 211 SPN: 3510 FMI: 4 Sensor Supply 2 Circuit- Voltage Below Normal or Shorted to Low Source