Paccar– Pagina 289– ⛽ Diezel365


Paccar

PACCAR MX (2004 Emissions) Fault Code: U1839 CAN Communication – Message (PTO) Out of Range, Remote PTO Governor Preprogrammed Speed Control Switch #2

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U1839 CAN Communication – Message (PTO) Out of Range, Remote PTO Governor Preprogrammed Speed Control Switch #2 SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3....

Meer lezen →


PACCAR MX (2004 Emissions) Fault Code: U183B CAN Communication – Message (TCFG2) Out of Range, Transmission Torque Limit from Transmission System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U183B CAN Communication – Message (TCFG2) Out of Range, Transmission Torque Limit from Transmission System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the...

Meer lezen →


PACCAR MX (2004 Emissions) Fault Code: U183C CAN Communication – Message (TRF1) Out of Range, Transmission Oil Temperature from Transmission System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U183C CAN Communication – Message (TRF1) Out of Range, Transmission Oil Temperature from Transmission System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the...

Meer lezen →


PACCAR MX (2004 Emissions) Fault Code: U183E CAN – Message (TRF1) Time-Out from Transmission System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U183E CAN – Message (TRF1) Time-Out from Transmission System SET CONDITIONS:This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No,...

Meer lezen →


PACCAR MX (2004 Emissions) Fault Code: U183F CAN Communication – Message (VDC1) Out of Range, VDC Brake Light Request from Brake System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U183F CAN Communication – Message (VDC1) Out of Range, VDC Brake Light Request from Brake System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did...

Meer lezen →