Paccar– Pagina 248– ⛽ Diezel365


Paccar

PACCAR MX (2004 Emissions) Fault Code: U1112 CAN – Message (SCR1) Time-Out from Aftertreatment System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U1112 CAN – Message (SCR1) Time-Out from Aftertreatment System SET CONDITIONS:This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No,...

Meer lezen →


PACCAR MX (2004 Emissions) Fault Code: U1114 CAN – Message (AT1T1l) Time-Out, DEF Tank Information from Aftertreatment System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U1114 CAN – Message (AT1T1l) Time-Out, DEF Tank Information from Aftertreatment System SET CONDITIONS:This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC...

Meer lezen →


PACCAR MX (2004 Emissions) Fault Code: U1118 CAN Communication – Message (EXH_GAS_CORR) Out of Range, NOx After SCR Reading Stable from Aftertreatment System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U1118 CAN Communication – Message (EXH_GAS_CORR) Out of Range, NOx After SCR Reading Stable from Aftertreatment System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3....

Meer lezen →


PACCAR MX (2004 Emissions) Fault Code: U111A CAN Communication – Message (EXH_GAS_CORR) Out of Range, Engine Out NOx Reading Stable from Aftertreatment System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U111A CAN Communication – Message (EXH_GAS_CORR) Out of Range, Engine Out NOx Reading Stable from Aftertreatment System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3....

Meer lezen →


PACCAR MX (2004 Emissions) Fault Code: U111B CAN Communication – Message (EXH_GAS_CORR) Out of Range, O2 Concentration Before Catalyst (Corrected) from Aftertreatment System

Geplaatst door Diezel Solutions op

PACCAR MX (2004 Emissions) Fault Code: U111B CAN Communication – Message (EXH_GAS_CORR) Out of Range, O2 Concentration Before Catalyst (Corrected) from Aftertreatment System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3....

Meer lezen →