Cumminz
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2961 PID: 412 SPN: 412 FMI: 0 Exhaust Gas Recirculation Temperature – Data Valid But Above Normal Operational Range – Least Severe Level. EGR temperature has exceeded the engine protection limit.
Geplaatst door Diezel Solutions op
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM. Possible causes: 1)Plugged or leaking EGR differential flow ports2)A malfunctioning EGR valve3)A stuck open turbocharger control valve4)A low reading from the EGR differential pressure sensor5)A low reading for the EGR valve position sensor6)High exhaust temperatures7)Low coolant level8)High coolant temperature9)An incorrect coolant/water mixture10)A stuck closed variable geometry turbocharger11)A fouled EGR cooler. Note: This fault code will most likely not be active with no load in the shop. The...
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2962 PID: 412 SPN: 412 FMI: 0 Exhaust Gas Recirculation Temperature – Data Valid But Above Normal Operational Range – Moderately Severe Level. EGR temperature has exceeded the engine protection limit.
Geplaatst door Diezel Solutions op
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM. Possible causes: 1)A fouled EGR cooler2)Plugged or leaking EGR differential flow ports3)A damaged EGR valve4)A stuck open turbocharger control valve5)A low reading from the EGR differential pressure sensor6)A low reading for the EGR valve position sensor7)High exhaust temperatures8)Low coolant level9)High coolant temperature10)An incorrect coolant/water mixture11)A stuck closed variable geometry turbocharger. Note: This fault code will most likely not be active with no load in the shop. The...
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2963 PID: 110 SPN: 110
Geplaatst door Diezel Solutions op
Verify the ECM calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM. Possible repairs: 1)Replace the engine coolant temperat2)If necessary, calibrate the ECM.
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2964 PID: 105 SPN: 105
Geplaatst door Diezel Solutions op
Verify the ECM calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, calibrate the ECM. Possible repairs: 1)Replace the intake manifold temperature sensor.
Cummins ISB6.7 CM2150 (2007-09) Fault Code: 297 PID: 443 SPN: 1388 FMI: 3 Auxiliary Pressure Sensor Input 1 Circuit – Voltage Above Normal or Shorted to High Source. High signal voltage detected at the OEM pressure circuit.
Geplaatst door Diezel Solutions op
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM.Possible causes: 1)Open return circuit in the harness, connectors, or sensor2)Signal circuit shorted to sensor supply or battery voltage. Possible repairs: 1)Replace the OEM pressure sensor.2)Replace the ECM.