Meteen naar de content

Telegram : @Diezel365

Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3838 PID: SPN: 2978 FMI: 9 Estimated Engine Parasitic Losses- Percent Torque- Abnormal Update Rate

Circuit DescriptionNormally, switches, accelerators, and other components are connected to the ECM directly through individual wires. Multiplexing allows those same components to be hard-wired to an OEM VECU or transmission electronic control unit (ECU) in the cab. Component values and states from components such as sensors, accelerators, and switches can then be transmitted from the OEM VECU to the Cummins? ECM over the SAE J1939 data link.

Messages sent from OEM VECUs or transmission ECUs are received by the Cummins? ECM and used for controlling the engine. The Cummins? ECM and OEM VECUs must be configured properly so that proper operation of the multiplexed components will occur.

Component LocationLocation of the relay is OEM dependent. Refer to the OEM service manual for the relay location.

Conditions for Running the DiagnosticsThis diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.

Conditions for Setting the Fault CodesThe OEM VECU determines there is a malfunction of the multiplexed accelerator pedal or lever sensor system.

Action Taken When the Fault Code is ActiveThe ECM illuminates the amber CHECK ENGINE lamp and/or malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.Conditions for Clearing the Fault CodeTo validate the repair, start the engine and let it idle for 1 minute.The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.The ECM will turn off the amber CHECK ENGINE lamp after the diagnostic runs and passes.For On-Board Diagnostics (OBD) engines, the ECM will turn off the MIL after three consecutive trips where the diagnostic runs and passes.The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.

Shop TalkThe J1939 multiplexing controller has detected that a message was not received when it was expected.

Reference the appropriate OEM wiring diagram when troubleshooting circuits utilize wiring supplied by the OEM.

For intermittent power supply and data link communication issues with aftertreatment components, it is highly recommended that the OEM Power Distribution Center fuses and relays be thoroughly checked for loose, missing, or intermittent connections.

Possible Cause:1) ECM calibration

Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3755 PID: SPN: 5394 FMI: 2 Aftertreatment Diesel Exhaust Fluid Dosing Valve- Data Erratic, Intermittent, or Incorrect
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3753 PID: SPN: 3713 FMI: 31 Diesel Particulate Filter Active Regeneration Inhibited Due to System Timeout- Condition Exists
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3751 PID: SPN: 4792 FMI: 7 Aftertreatment SCR Catalyst System- Mechanical System Not Responding or Out of Adjustment
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3749 PID: SID 254 SPN: 3226 FMI: 20 Aftertreatment Outlet Nox Sensor- Data Not Rational- Drifted High
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3748 PID: SPN: 3216 FMI: 20 Aftertreatment Intake Nox Sensor- Data Not Rational- Drifted High
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3737 PID: SID 115 SPN: 1675 FMI: 31 Engine Starter Mode Overcrank Protection- Condition Exists