Meteen naar de content

Telegram : @Diezel365

Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3186 PID: SPN: 1623 FMI: 9 Tachograph Output Shaft Speed- Abnormal Update Rate

Circuit DescriptionNormally, switches, accelerators, and other components are connected to the engine electronic control module (ECM) directly through individual wires. Multiplexing allows those same components to be hard wired to an original equipment manufacturer (OEM) vehicle electronic control unit (VECU) or transmission electronic control unit (ECU) in the cab. Component values and states from components such as sensors, accelerators, and switches can then be transmitted from the OEM VECU to the Cummins? ECM over the SAE J1939 data link.

Messages sent from OEM VECUs or transmission ECUs are received by the Cummins? ECM and used for controlling the engine. The Cummins Inc. ECM and OEM VECU(s) must be configured properly so that proper operation of the multiplexed components will occur.

Component LocationThe SAE J1939 data link wiring and the SAE J1939 devices vary by OEM options.

Conditions for Running the DiagnosticsThis diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.

Conditions for Setting the Fault CodesThe ECM did not receive a message from the multiplexed device.

Action Taken When the Fault Code is ActiveThe ECM illuminates the amber CHECK ENGINE lamp and/or Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails.Conditions for Clearing the Fault CodeTo validate the repair, start the engine and let it idle for 1 minute.The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.The ECM will turn off the amber CHECK ENGINE lamp after the diagnostic runs and passes.For On-Board Diagnostics (OBD) engines, the ECM will turn off the MIL after 3 consecutive trips where the diagnostic runs and passes.The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.

Shop TalkWhen this fault code is active, some multiplexed devices may not function as desired.

This fault can occur for the following reasons:

When the ECM is set up properly (components enabled and OEM VECU source addressed correctly) to receive information from an OEM VECU, but the OEM VECU is actually transmitting a message that says that component is not available for multiplexing. This can be caused when a multiplexed component is enabled in the Cummins? ECM, but the OEM VECU source address of the VECU transmitting the component message is incorrect in the Cummins? ECM, or the OEM VECU is not set up to transmit the multiplexed component message.This fault can also be caused by a bad J1939 data link connection between the OEM VECU and Cummins? ECM, a bad connection between the component and the OEM VECU, bad OEM VECU or bad Cummins? ECM. It may be necessary to contact the OEM for proper multiplexing configuration.It is possible to use INSITE? electronic service tool to monitor multiplexed components.

Possible Cause:1) OEM harness2) ECM calibration

Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3168 PID: SPN: 3936 FMI: 16 Aftertreatment Diesel Particulate Filter System- Data Valid But Above Normal Operating Range- Moderately Severe Level
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3167 PID: SID 382 SPN: 3556 FMI: 18 Aftertreatment Doser- Data valid But Below Normal Operating Range- Moderately Severe Level
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3165 PID: SPN: 4363 FMI: 0 Aftertreatment 1 SCR Outlet Temperature- Data Valid But Above Normal Operating range- Most Severe Level
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3164 PID: SPN: 4360 FMI: 15 Aftertreatment SCR Intake Temperature- DataValid But Above Normal Operating Range- Least Severe Level
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3151 (MR) PID: SPN: 4794 FMI: 31 Aftertreatment SCR catalyst System Missing- Condition Exists
Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3151 (HD) PID: SPN: 4364 FMI: 18 Aftertreatment SCR catalyst Conversion Efficiency- Data Valid But Below Normal Operating Range- Moderately Severe Level