Paccar– Page 268– ⛽ Diezel365


Paccar

PACCAR MX (2004 Emissions) Fault Code: U1780 CAN – Message (TSC1 yye) Time-Out

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1780 CAN – Message (TSC1 yye) Time-Out SET CONDITIONS:This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No, repair successful–...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1781 CAN – Message (TSC_PE) Time-Out

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1781 CAN – Message (TSC_PE) Time-Out SET CONDITIONS:This DTC is set when the repetition rate of the received CAN message is lower than expected or when the message is not received at all. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No, repair successful– Yes,...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1788 CAN Communication – Message (PROPB_EST) Not Available, Coolant Temperature from Retarder System

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1788 CAN Communication – Message (PROPB_EST) Not Available, Coolant Temperature from Retarder System SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is not available. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the DTC come back?– No, repair successful– Yes, repair unsuccessful POSSIBLE CAUSES:A...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U1789 CAN Communication – Message (PROBA_BBM_to_Eng) Out of Range, Starter Interrupt from Body Builder Module

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U1789 CAN Communication – Message (PROBA_BBM_to_Eng) Out of Range, Starter Interrupt from Body Builder Module SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the...

Read more →


PACCAR MX (2004 Emissions) Fault Code: U178A CAN Communication – Message (PROBA_BBM_to_Eng) Out of Range, ESC Enable from Body Builder Module

Posted by Diezel Solutions on

PACCAR MX (2004 Emissions) Fault Code: U178A CAN Communication – Message (PROBA_BBM_to_Eng) Out of Range, ESC Enable from Body Builder Module SET CONDITIONS:This DTC is set when a CAN message is received correctly, but the content (signal value or status) is out of the expected range. DIAGNOSTIC CONDITION:The diagnostic runs continuously when the ignition is keyed on or when the engine is running. CORRESPONDING OBD READINESS MONITOR:None RESET CONDITION:The DTC changes to inactive after the diagnostic runs and passes. REPAIR VERIFICATION:1. Clear all DTCs.2. Test drive or operate the vehicle to meet the diagnostic conditions and set conditions.3. Did the...

Read more →