Cumminz
Cummins ISB4.5 CM2150 Fault Code: 2182 PID: 478 SPN: 1072 FMI: 3 Engine Brake Actuator Driver 1 Circuit – Voltage Above Normal or Shorted to High Source.
Posted by Diezel Solutions on
Circuit DescriptionThis circuit can be used to control either an exhaust brake or an engine brake depending on the application. The engine control module (ECM) controls engine brakes on cylinders 1, 2, and 3 by sending a signal on the engine brake solenoid number 1 signal circuit. If an engine brake is installed, there will be a jumper harness from this connector to the engine brake pass-through connectors on the rocker lever housing. Component LocationThe engine brake solenoids are located under the valve cover. The engine brake solenoids are controlled through the engine harness from the ECM. Conditions for Running...
Cummins ISB4.5 CM2150 Fault Code: 2182 PID: 478 SPN: 1072 FMI: 3 Engine Brake Actuator Driver 1 Circuit – Voltage Above Normal or Shorted to High Source.
Posted by Diezel Solutions on
Circuit DescriptionThis circuit can be used to control either an exhaust brake or an engine brake depending on the application. The engine control module (ECM) controls engine brakes on cylinders 1, 2, and 3 by sending a signal on the engine brake solenoid number 1 signal circuit. If an engine brake is installed, there will be a jumper harness from this connector to the engine brake pass-through connectors on the rocker lever housing. Component LocationThe engine brake solenoids are located under the valve cover. The engine brake solenoids are controlled through the engine harness from the ECM. Conditions for Running...
Cummins ISB4.5 CM2150 Fault Code: 2183 PID: 477 SPN: 1072 FMI: 4 Engine Brake Actuator Driver 1 Circuit – Voltage Below Normal or Shorted to Low Source.
Posted by Diezel Solutions on
Circuit DescriptionThis circuit can be used to control either an exhaust brake or an engine brake depending on the application. The engine control module (ECM) controls engine brakes on cylinders 1, 2, and 3, by sending a signal on the engine brake solenoid number 1 signal circuit. If an engine brake is installed, there will be a jumper harness from this connector to the engine brake pass-through connectors on the rocker lever housing. Component LocationThe engine brake solenoids are located under the valve cover. The engine brake solenoids are controlled through the engine harness from the ECM. Conditions for Running...
Cummins ISB4.5 CM2150 Fault Code: 2185 PID: SID 232 SPN: 3512 FMI: 3 Sensor Supply 4 Circuit – Voltage Above Normal or Shorted to High Source.
Posted by Diezel Solutions on
Circuit DescriptionSensor supply 4 of the engine control module (ECM) provides a 5 volt supply to the accelerator pedal position sensor. The accelerator position sensor is a Hall effect sensor attached to the accelerator pedal. The accelerator position sensor varies the signal voltage to the ECM as the accelerator pedal is depressed and released. Low signal voltage is received by the ECM when the accelerator pedal is at 0 percent. A high signal voltage is received by the ECM when the accelerator pedal is at 100 percent. The accelerator pedal position circuit contains an accelerator pedal position 5 volt supply,...
Cummins ISB4.5 CM2150 Fault Code: 2186 PID: SID 232 SPN: 3512 FMI: 4 Sensor Supply 4 Circuit – Voltage Below Normal or Shorted to Low Source.
Posted by Diezel Solutions on
Circuit DescriptionSensor supply 4 of the engine control module (ECM) provides a 5 volt supply to the accelerator pedal position sensor. The accelerator position sensor is a Hall effect sensor attached to the accelerator pedal. The accelerator position sensor varies the signal voltage to the ECM as the accelerator pedal is depressed and released. Low signal voltage is received by the ECM when the accelerator pedal is at 0 percent. A high signal voltage is received by the ECM when the accelerator pedal is at 100 percent. The accelerator pedal position circuit contains an accelerator pedal position 5 volt supply,...